View in 
get a quote



This quantum diamond magnetometer and its experiments will introduce students to the concepts of quantum sensing. The design of the quNV is based on recent achievements of scientific research and demonstrates quantum sensing in a simple and user friendly system for student lab courses at colleges and universities.

The core of the quNV is a HPHT diamond with an ensemble of nitrogen-vacancy (NV) centers. The NV centers can be excited by light in the visible spectrum. The excited state decays back to the ground state either directly or via an intermediate shelving state with different fluorescence intensity. The decay path depends on the electron spin of the NV centers. Thus, the electron spin can be read out optically.

Key Features

Probe: HPHT Diamond
Excitation: 516 nm Diode Laser, CW and Pulsed
Microwave: 4 GHz RF Sweep Generator, CW and Pulsed
Detection: Photodiode, Control & Read-Out Unit
Optics: 20x Objective
Magnetic Field: 3 Helmholtz Coils

Core Components

The core of the base quNV is a HPHT diamond with an ensemble of nitrogen-vacancy (NV) centers. The NV centers can be excited by light in the visible spectrum. The excited state decays back to the ground state directly or via an intermediate shelving state with different fluorescence intensity. The decay path depends on the electron spin of the NV centers. Thus, the electron spin can be read out optically.

Laser Excitation

The NV centers are excited by a powerful 50mW continuous wave laser with a wavelength of 516nm. The laser is collimated and expanded to create optimal conditions for the following microscope objective. The objective focuses the laser light onto the nitrogen-doped diamond.

Diamond Sample Stack

The laser spot focused by the objective hits the diamond, which is built into a circuit board. The microwave antenna is also integrated in the circuit board. It is mounted on a stack to which the specimen itself is attached. The circuit board with the antenna and the diamond can be replaced by other boards with different diamonds, depending on the experiment.

Microwave Sweep and Pulse

The microwave radiation is emitted by the antenna within the circuit board. It is controlled by electronic components in the base of the quNV. The microwave can be varied in amplitude, swept in frequency and even pulsed.

Helmholtz Coils

The three Helmholtz coils surround the sample stack. These three coils generate a homogeneous magnetic field as a bias for the NV centers. All three coils can also be controlled individually to adjust the field in three dimensions. The coils are equipped with temperature monitoring sensors for safety reasons.

Pattern Generator

The electronics in the base of the quNV also includes a pattern generator. This pattern generator can control and pulse the laser, the microwave and the photodiode for fluorescence readout. Different pulse patterns can be applied to all three components with the desired time intervals in between. The cw laser can be pulsed for excitation and readout, the microwave for the emission of ? and ?/2 pulses and the photodiode gated.


The fluorescence from the excited NV center is also collected by the microscope objective and returned to the unit on top of the instrument by the same optical path. There, the red fluorescence is separated from the green excitation laser by a dicroic mirror. After two mirrors for proper alignment, the fluorescence is filtered by a bandpass to measure only the red fluorescence rather then the excitation laser nor the environment. In the end, the light is focused on the active region of the fast photodiode.


In a basic measurement, a magnetic bias field by the Helmholtz coils is set. Then the laser excites the NV centers in the diamond, which fluoresce in the red spectrum. That light is detected by the photodiode. Now the microwave frequency is swept. Plotting this frequency versus the fluorescence intensity shows the resonance frequencies of the NV centers.


The dynamics of the NV center allow applications like spin initialization and state readout. Therefore, the center is suitable for quantum sensing applications like magnetic field sensing, spin relaxation time measurements and optically detected magnetic resonance (ODMR).

Due to their scalability, long coherence times and ability for interaction with photons, NV centers are of high interest for research in quantum information processing. Qubits can be defined as spin states of single electron or nuclear spins.

Possible applications of the quNV are:
• Student lab course experiments
• Demonstration experiments in lectures
• Hands-on experiments for science centers
• Project kits for students’ research centers

Variants and Upgrades

The core unit of the NV quantum sensing kit can be further supplemented and upgraded to either perform experiments with a single NV center or use the setup as a full quantum microscope.

Microscopy Variant

This variant will allow you to take a deeper look at the application of NV center microscopy for magnetic analysis of different samples, e.g., geological or biological.

At the heart of the microscopy variant, there is a chemically pure CVD diamond with a uniform distribution of NV centers right below the surface of the diamond in order to best couple them to the magnetic properties of your sample.

An objective with the desired magnitude and the matching optical setup will complete the arrangement for microscope images of magnetic fields.

Instead of a photodiode or the APD of the single photon variant, a camera can be used to achieve a wide field of view of the diamond and sample at once. One can then show how an ODMR measurement can be performed on this field of view to determine the magnetic field at every point at once.

Sensing Kit

Try out the effect a differently doped diamond can have and use them to perform microscopic measurements on different samples.

A selection of diamonds doped in different depth layers and with a varying concentration of NV centers pointing in different directions.

Different cut and polished rock samples showing interesting magnetic properties from the field of geology.

Single Photon Variant

With this variant you’ll obtain the ability to locate and manipulate a single NV center in a specially prepared diamond.

A high NA objective and the following confocal microscope setup make it possible to couple a high percentage of emitted fluorescence photons into a fiber leading to the detectors.

Specially made chemically pure CVD-Diamonds with an ultra-low concentration of NV centers are at the core of this variant to ensure single and isolated NV centers in the focal spot.

High precision piezo stages allow for precise control and scanning of the viewing area in order to find a defect and stay focused on it.

A fiber based high efficiency avalanche photodiode with a sharp time resolution rounds up the system.

HBT Upgrade
Measure the g(2) Function to prove that the emitted photons cannot be split up and that an NV center is a source of real single photons.

The single photons are led to a beam splitter to try and split them up.

With an additional single photon detector, one can make measurements on the photon statistics of the emitted photons.

With technology borrowed from our quTAG time tagger series, the APD signals can be analyzed down to the picosecond time domain to show a high resolution g(2) dip.


Here is a list of the experiments you can do with the quNV:
   • NV Center Fluorescence
   • Optically Detected Magnetic Resonance (ODMR) Microscopy
   • Zeeman Effect
   • Orientation of NV-Centers in the Lattice
   • Magnetic Field Sensing
   • Spin Initialization and Readout (T1 time)
   • Rabi Oscillations
   • Pulse Sequence Development
   • Coherence Times T2
   • Ramsey sequence
   • Dynamical Decoupling, Hahn Echo